DoubleButton

Wireless hold-up device with advanced protection against accidental pressing

FAQ

The identifier (ID) is the serial number of the device. It is located under the QR code on the body, board, and packaging of the device.

ID at the bottom of the box

ID under the lid

The ID can also be found in the device states in the Ajax app.

  1. Sign in to the Ajax app.
  2. Select the required hub from the list if you have several of them or if you are using a PRO app.
  3. Go to the Devices menu.
  4. Select a device from the list. Device ID information is located at the bottom of the status screen.
Copied

You can test the radio communication by pressing the device’s button.

To test SpaceControl, press the disarm button to avoid triggering an alarm. If the command is delivered, the LED will light up green. The red LED indicates that the command has not been delivered.

For Button, it’s better to enable Control mode and temporarily disable scenarios. After pressing the button, the green LED will indicate the delivery of the command. If Button’s LED lights up red — command has not been delivered.

To test DoubleButton, press one of two available buttons: the device will light up green (command was delivered) and then red (no alarm was raised). The LED will light up red twice if the command is not delivered.

Copied

Button is a wireless panic button with protection against accidental pressing and an additional control mode for automation devices.

DoubleButton is a wireless hold-up device. It has two tight buttons and a plastic shield to protect against accidental pressing.

Button DoubleButton
Buttons 1 2
Shield to protect against accidental pressing +
Control mode support +

 

Copied

This option is not provided.

Copied

DoubleButton works with Ajax hubs only. No provision is made for connection to ocBridge Plus and uartBridge integration modules.

Copied

The reserve QR code is located on the board inside the button.

ajax doublebutton qr code

In addition, you can see the button ID in the Ajax app if the DoubleButton has been linked to the hub. The ID is available in the device States (Ajax app → Devices → DoubleButton).

Copied

There are two ways to activate the alarm: by short or long (more than 2 seconds) pressing of both buttons. You cannot change pressing duration.

Copied

The ability to manage security modes with DoubleButton is not provided. You can use SpaceControl and KeyPad for this.

Copied

The charge level updates by pressing a button only, and not in the background. Press one of the device buttons to update the battery charge status in the app.

Copied

The maximum communication range between the hub and the DoubleButton is 1300 meters without obstacles between the devices.

If DoubleButton commands are not delivered to the hub, choose a different button location, or use a radio signal range extender.

Copied

DoubleButton can operate with one hub only. When added to a new hub, the button will no longer send alarms to the old one.

Copied

DoubleButton can only operate as a hold-up device. It is not possible to specify the type of alarm for the button.

Copied

For DoubleButton, scenarios by alarm are only available. Automation devices control mode is not provided.

Copied
  1. Choose a location to install the holder.
  2. Press the button to test whether the commands are delivered to a hub. If not, choose another location or use the radio signal range extenders.

    When routing Button/DoubleButton through range extender, keep in mind that it does not automatically switch between a range extender and a hub. You can assign a button to a hub or another radio signal range extender in the Ajax app.

  3. Fix Holder on the surface using the bundled screws or double-sided adhesive tape.
    ajax holder button
  4. Put the button into the holder.
    ajax holder button
Copied

Holder is needed to securely fix Button/DoubleButton on a surface. For example, under the bed or near the bedhead.

Copied

The firmware version can be found in the device states in the Ajax app.

  1. Sign in to the Ajax app.
  2. Select the required hub from the list if you have several of them or if you are using a PRO app.
  3. Go to the Devices menu.
  4. Select a device from the list. The firmware version information is located on the status screen at the bottom.
Copied

Featured articles

How to disable device events once for a time the armed mode is active

How to replace the battery in DoubleButton

What functions depend on the device firmware version

Spelling error report

The following text will be sent to our editors: