How to receive an alarm triggered by an attempt to open a door lock

Updated

Ajax security system can send an alarm triggered by an attempt to open a door lock. Therefore, the robbers will be detected prior to gaining access to the premises. The sirens are likely to interrupt the robbery attempt. And the sooner the intruder is detected, the higher the chances are of preserving the property and the health of the residents.

The door lock alarm operates as follows. Miniature switches are installed inside the holes intended for crossbars of the locks inside the door frame. These switches are connected to the DoorProtect, DoorProtect Plus opening detector or the Transmitter and MultiTransmitter integration modules. When an attempt is made to open the lock, the switch button is released and the detector raises an alarm — the sirens are switched on and the hub notifies users and the security console. However, even if one of the locks is opened, the remaining ones will keep the door closed.

ajax doorprotect

If you want to connect several wired detectors at once, we recommend using MultiTransmitter. This integration module allows simultaneous connection of 18 wired devices.

In order to detect the opening of the lock, microswitches or limit switches can be used:

ajax doorprotect

A microswitch (on the left) and a limit switch (on the right)

It is recommended to use switches with a wheel on the lever as they last longer.

If you use a door lock alarm, the Ajax security system must be disarmed prior to opening the lock via App, a SpaceControl key fob or from a KeyPad keyboard installed in the vestibule in front of the entrance.

If your hub is connected to a centralized monitoring station, the installation of a door lock alarm must be coordinated with your security company

How to choose devices to detect the opening of the lock

Door lock alarm can be implemented using DoorProtect and DoorProtect Plus opening detectors or a Transmitter or MultiTransmitter integration modules. In any case, when the switch button is triggered, the users of the security system and the security company will receive an alarm notification indicating the source of the alarm: opening detector (remote contact terminal) or integration module.

DoorProtect / DoorProtect Plus application features:

ajax doorprotect

+ You do not need to buy a new Ajax device if the door has an opening detector installed.

It is not recommended to use cables longer than 5 meters to connect switches.

NO (normally open) or NO / NC switches can be connected to the detector.

Transmitter / MultiTransmitter application features:

ajax transmitter

+ The maximum cable length for connecting switches is 150 meters (400 meters for MultiTransmitter).

+ Switches of any type (NC / NO) can be connected to the integration module.

You must purchase a Transmitter/ MultiTransmitter integration module.

In order to ensure correct operation of the door lock alarm, use switches of the same type (NC or NO).

Option 1: How to connect switches to the opening detector

Measure the cable length in advance to connect the switches to the detector. When measuring the length, keep in mind that NO type switches are connected in series.

Connect the switches in series and connect to the remote contact terminal of the detector as shown in the diagram:

ajax doorprotect plus

In the Ajax app:

  1. Go to the detector settings (Devices DoorProtect / DoorProtect PlusSettings ) and enable the External Contact Terminal enabled option.
  2. Disable the Delay When Entering, if enabled. When the delay is enabled, the alarm does not arrive instantly.
  3. Click Back to save the settings
  4. Open the detector menu (Devices DoorProtect / DoorProtect Plus). In the Secondary detector field, write Open. Simulate closing of the door by holding down the buttons of all switches. The status will change to Closed. If the status does not change, check the connection of the switches to the detector.

Option 2: How to connect switches to the integration module

Measure the cable length in advance to connect the switches to the device. When measuring the length, keep in mind that NO switches are connected in series, and NC are connected to the Transmitter / MultiTransmitter in parallel.

If you use NO switches: connect the switches in series and then connect to the alarm contact terminals of the Transmitter / MultiTransmitter as shown in the diagram:

ajax transmitter

If you use NC switches: connect the switches in parallel to the alarm contact terminals of the Transmitter / MultiTransmitter as shown in the diagram:

ajax transmitter

In the Ajax app:

  1. Go to the Transmitter settings (Devices TransmitterSettings ) and select the External contact mode according to the type of switches: Normally open (if you use NC switches) or Normally closed (if you use NO switches).
  2. Change settings: Tamper modeNormally open (to avoid receiving messages about the open tamper of the device) and External detector power supplyAlways disabled.
  3. Disable Siren Activation if an alarm is detected and Delay When Entering. When the delay is enabled, the alarm does not arrive instantly.
  4. Click Back to apply the settings.

    To connect switches to MultiTransmitter, use the integration module user’s manual.

  5. If you are connected to the security console, inform the security company in advance about the device test. Hold down the buttons of all switches and arm the security system. Wait 30 seconds for the system to become armed and release the button of one of the switches — an alarm will be received by the Ajax app. If the alarm does not arrive, check the connection of the switches to the device.
  6. After ensuring that the system is functioning properly, enable the activation of the siren in the settings of the integration module if you want the siren to respond to an attempt to open the lock.

How to install switches within the door frame

If you have not yet installed a door or you are planning to change it, provide a place for switches and cabling inside the door frame.

In order to mount switches inside an already installed door, implement the following for each of the locks:

  1. Make holes for cable routing through the door frame in advance.
  2. If several turns are required to close a lock, select the number of turns (preferably more than one) taking into account the length of the crossbars in the relevant lock state.

    Note that the specified number of turns will be required to close the lock. With a larger number of turns, there is a risk of breaking the switch, and with a smaller number of turns, the crossbars will not clamp the switch button, and, therefore, the lock will be considered open.

  3. Check if there is enough space to install the switch in the crossbar hole. If there is not enough space, provide a cavity for the switch.
  4. Temporarily fasten the switch in the crossbar hole so that the crossbars clamp the switch button when the door is closed.
  5. Draw the wires through the door frame and connect to the device.
  6. Test the operation of the door lock alarm. If the alarm is working properly, hide the wires, and fasten the switches and the detector securely.

If the system does not respond to the opening and closing of the locks, check the connection of the switches with the detector and also make sure that the crossbars clamp the switch button.

In order for the door lock alarm to respond to the opening of a door lock, even if the system is disarmed, enable the Always active option in the detector settings.

Spelling error report

The following text will be sent to our editors: